Windshield Repair Kit
designed to be repaired within minutes
almost all kinds of car glass type
"Triplex", including rounded glasses,
Repairs damage in a shape resembling
Star, as well as for repairing ordinary cracks, not
exceeding 30 cm in length. The kit includes all
necessary for repair. Components do not require
mixing. The adhesive base hardens under the influence
natural daylight.
ADVANTAGES OF THE KIT
• Ease of use
• Everything you need for repair is included in the kit
• Easy to use
• Fast curing of the adhesive base
• Repair of damage such as: chips ("bull's eye"),
Stars and cracks.
INTENDED FOR REPAIR:
• Damage to automotive triplex
glasses of the following types: chips, "stars",
"Cobwebs" and ordinary cracks (up to 30 cm in length).
INSTRUCTIONS FOR USE:
For glass repair, damage in shape
chips, "cobwebs", "stars"
Carry out repairs in dark places when
surface temperature of the wind farm being repaired
glass from ° С +10 to ° С +23.9. To avoid damage
the surface of the body should not be exposed to resin
onto the surface of the car.
1. Degrease the windshield around the place
damage to the inside and outside of the windshield with
using a swab soaked in alcohol
substance. Remove shards of glass from the place
damage. To avoid resin dripping
place a piece under the surface to be repaired
fabrics.
2. Punch a hole in the center of the adhesive disc.
Remove the protective pad from ONE side
disk. Align the hole in the center of the disc with
center of the damaged area. (Ledge on disc
must be upward). Tightly
press the adhesive disc against the glass. Make sure of
contact of the entire surface of the disc with
glass surface. Make sure that the
disk surface on the inner side of the windscreen
there are no air bubbles in the glass.
3. Remove the protective strip from the OTHER side
adhesive disc. Combine the "pedestal" with adhesive
after making sure that the protrusion is on
The “pedestal” points upwards and matches the hole in the adhesive disc. Press down STRONGLY
Pedestal to the adhesive disc and make sure
absence of air bubbles on its surface.
4. Carefully remove the cap from the syringe, turn over
syringe up, gently push the plunger until
until air comes out of the syringe (In order to
to avoid injury, do not bring the syringe to the face).
Remove resin from the syringe after
air removal. Careful tight
insert the syringe tip into the "pedestal".
5. Holding the syringe with one hand, pull the plunger
to myself. PUSH THE PISTON FOLLOWS
CAUTION UNTIL YOU DO NOT FOLLOW
ITS STOP. (In the event that the piston
too much force will be applied
it may slip out of the grooves inside
syringe. In this case, you need to insert
the plunger into the syringe, remove it (syringe) from
"Pedestal", turn the syringe up and again
remove air from the syringe by pressing on it
piston.).
6. After the piston stops, leave
the syringe is stationary for a few seconds, after which
release the piston sharply. Repeat this process 10
time, each time leaving the syringe motionless for
a few seconds before releasing it.
It is possible that to assess the results of the repair
it will be necessary to highlight the refurbished
surface with a bright light source. When
the appearance of air bubbles at the place of repair,
repeat points of this instruction No. 5 and No. 6.
7. Move the car under direct sunlight
rays and leave for 30 minutes to dry completely
components. (On cloudy days for full
drying takes 1 hour).
8. Remove the syringe from the "pedestal" and close it
cap. Remove the adhesive disc from the glass. IN
use a secure
blade or tongs.
9. If the surface is not level, remove
excess dried resin with a safe
blades. Wipe the glass with alcohol
swab.
For repairing glass cracks up to 30 cm long
Carry out repairs in shaded areas when
surface temperature of the wind farm being repaired
glass from ° C 10 to ° C 23.9. To avoid damage
the surface of the body should not be exposed to resin
onto the surface of the car.
1. Degrease the windshield around the place
damage to the inside and outside of the windshield with
using a swab soaked in alcohol
substance.
2. Remove the cap from the syringe. Squeeze out a little
amount of resin and distribute it throughout
crack length.
3. After applying the resin, place on the crack
2 ”X3” adhesive plastic film. Use as many small pieces of film as
necessary to cover the entire surface
cracks. When laying film on glass, it is not required
make an effort.
4. Press lightly on the inside of the windshield
glass along the entire length of the crack. Thus,
the edges of the cracked glass will spread apart and
the space between them will seep resin.
Excessive application of force to the glass will result in
crack growth.
5. Inspect the repair results from both sides
glass. Inspect the repaired site under
an angle of 45 ° - cracks should not be visible. If a
cracks are visible - repeat the points of this
instructions No. 3 and No. 4 ..
6. If the repair results are positive, leave
car in a sunny place for 30 minutes. (in
cloudy days need 1 hour).
7. After the resin has cured, carefully remove from
glass surface with adhesive film. Through
Scrape off the supplied safety blade
excess rubber from the glass surface. Wherein
hold the blade at a 45 ° angle
relation to the glass surface.
8. After that, clean the glass with a swab,
impregnated with an alcohol-containing substance.