Designed for use in the transmission of vehicles with a range of up to 100,000 km. Purpose: Processing of mechanical gearboxes, transfer cases, car bridges.
Added to gear oil. Dosage: one bottle of 95 ml. / 2 liters of gear oil.
The action of the product is aimed at the formation of a protective layer of nanoceramics at the molecular level.
As a result of using this product:
- Improves the smoothness of the ride and gear shifting
- Reduced vibration and noise
- The resource of the mechanism is extended

ATTENTION! Read the instructions carefully before use.
Series: PROTECTION
FORSAN nanoceramics ™ Transmission is a product of nanotechnology that provides protection against wear of component parts
transmissions. Designed for bridges, gearboxes, manual transmissions of cars with less mileage
100,000 km
The result of application is:
Reduced vibration and noise
Improved ride and gear shifting
Reduced fuel consumption
Reduced wear during "cold driving"
TRANSMISSION PROCESSING TECHNIQUE
Transmission processing is performed ONCE according to the table (Table 1).
Table # 1. FORSAN nanoceramics consumption rate table Transmission
Processing order:
1. Warm up the transmission after driving 5-10 km.
2. Prepare a bottle of FORSAN nanoceramics ™ Transmission.
3. Make sure the vial is at room temperature and shake vigorously for 1-2 minutes.
4. Add the contents of the bottle to the case of the gearbox, transfer case, drive axle through
oil filler neck or hole. Dosage according to the table.
5. If sediment remains in the bottle, add a small amount of regular oil, shake thoroughly and
pour into the oil filler neck.
6. After filling, you need to drive 5-10 km using all gears, including reverse (for several
minutes every).
ATTENTION!
- FORSAN nanoceramics ™ vial Transmission is not intended for automatic transmissions.
RECOMMENDATIONS:
- To increase the effect and stabilize the result of application, it is recommended to make additional
transmission treatment - after 50,000 km or 1 year, whichever comes first.
- To increase the effect and stabilize the result, it is recommended to carry out a complex treatment of the car,
using additionally FORSAN nanoceramics ™ vials Engine series: PROTECTION
- If additives with molybdenum, graphite, etc. were used. it is necessary to change the oil.
1 To obtain the required dosage, use an additional bottle of FORSAN nanoceramics ™ Transmission series:
PROTECTION.
Transmission oil volume (l) Dosage1
for full processing of the node
from 0.5 to 1 ½ bottle
from 1 to 2 1 bottle
from 2 to 3 1½ bottles
from 3 to 4 2 bottles

Processing order:
1. Warm up the transmission after driving 5-10 km.
2. Prepare a bottle of FORSAN nanoceramics ™ Transmission.
3. Make sure the vial is at room temperature and shake vigorously for 1-2 minutes.
4. Add the contents of the bottle to the case of the gearbox, transfer case, drive axle through
oil filler neck or hole. Dosage according to the table.
5. If sediment remains in the bottle, add a small amount of regular oil, shake thoroughly and
pour into the oil filler neck.
6. After filling, you need to drive 5-10 km using all gears, including reverse (for several
minutes every).
ATTENTION!
- FORSAN nanoceramics ™ vial Transmission is not intended for automatic transmissions.
RECOMMENDATIONS:
- To increase the effect and stabilize the result of application, it is recommended to make additional
transmission treatment - after 50,000 km or 1 year, whichever comes first.
- To increase the effect and stabilize the result, it is recommended to carry out a complex treatment of the car,
using additionally FORSAN nanoceramics ™ vials Engine series: PROTECTION
- If additives with molybdenum, graphite, etc. were used. it is necessary to change the oil.
1 To obtain the required dosage, use an additional bottle of FORSAN nanoceramics ™ Transmission Series: PROTECTION.